Psiber ReportXpert User s Manual A Installation Psiber CONTENTS Table of Contents Psiber 1 User s Manual 1 CONTENTS 2 Installation 4 Installation and Setup 4 Installing PDF Writer 4 Upgrade 4 Project Management 6 Creating a new project 6 Importing Test records 7 Closing a project 8 Opening an existing project 8 Exporting to a project pack 9 Opening a project Pack 9 Editing Site Name 10 Organizing results into Hierarchy 11 Viewing Plots 12 Viewing Plots a W
PlNGER NETWORK IP TESTER USER S GUIDE psiber BOX CONTENTS Pinger Network IP Tester AC Adapter Four AA Alkaline Batteries User Guide BATTERY The Pinger operates on four AA alkaline batteries Remove the battery cover at the back of the unit and insert the batteries with the orientation as shown Battery polarity is marked inside the battery well for reference TECHNICAL OVERVIEW The Pinger Network IP Tester uses the PING function to sen
UPDATE PINGER SCREEN The Pinger Plus firmware can be updated over the network as new revisions are released Notice of a new revision will be provided on the Psiber web site www psiber com Download the new firmware file connect the Pinger Plus to the network go to the Update Pinger Setup screen press the Select function key and the unit will Link to the network and enable the firmware update mode Next run the down loaded file on the computer The program will ask for the cu
LINK SIGNAL TYPE Three different signals can be used to establish a Link a Link Code Word an NLP oran MLT 3 waveform it T he Link Code Word is specific in both Link speed and duplex mode The NLP s specific in speed 10Mbps but ambiguous in duplex mode half or full The MLT 3 waveform is also specific in speed 100Mbps out ambiguous in duplex mode Duplex modes for equipmentthatuse NLP or MLT 3 signaling must be known to ensure proper Link operation Example a s
PORT IDENTIFICATION Connect the Model 10 to a wall outlet select Port ID and then go to the hub or switch connected to the wall outlet The Link light for the port connected to the wall outlet will blink at a rate similar to the pattern selected on the Model 10 Three patterns are provided SHORT CIRCUIT TEST Connect the Model 10 to a cable with the test leads and select Short If a short is detected the LED will stay on continuously otherwise the LED will blink The shor
Psiber WX4500 User s Manual Psiber Data Pte Ltd Notices Psiber Data Pte Ltd No part of this manual may be reproduced in any form or by any means including electronic storage and retrieval or translation into a foreign language without prior agreement and written consent from Psiber Data as governed byinternational copyright laws Psiber Data Pte Ltd uw Manual Part Number 3000 0012 WX User Guide Edition First Edition November 10 2
manual Wifi Planner Contents 1 Introduction 2 1 1 PC 1 1 PC Hardware Requirements 3 1 2 Installation and Activation 3 1 3 Product Updates 5 2 Fundamentals of Wireless Network Planning 5 2 1 Standardization in Wireless Networking 5 2 1 1 The IEEE 802 11 b Specification 5 2 1 2 The IEEE 802 11 g Specification 6 2 1 3 The IEEE 802 11 a Specification 6 2 1 4 The IEEE 802 11 h Specification 6 2 2 Frequencies and Channels 6 2 3 Ce
UPDATE PINGER SCREEN The Pinger Plus firmware can be updated over the network as new revisions are released Notice of a new revision will be provided on the Psiber web site www psiber com Download the new firmware file connect the Pinger Plus to the network go to the Update Pinger Setup screen press the Select function key and the unit will Link to the network and enable the firmware update mode Next run the down loaded file on the computer The program will ask for the cu
LINK SEARCH SCREEN The Link Search setup screen is used to set the length of time that the Pinger Plus will monitor a wire pair for Link signals Normal about 2 5 seconds is the default setting or use the Up Down cursor key to select the Long setting about 5 seconds Some switches especially if configured for VoIP require a longer time to complete Link negotiations and the Long setting will provide more consistent Link detection UPDATE PINGER SCREEN The Pinger Plus firmwar
LINK SEARCH SCREEN The Link Search setup screen is used to set the length of time that the Pinger Plus will monitor a wire pair for Link signals Normal about 2 5 seconds is the default setting or use the Up Down cursor key to select the Long setting about 5 seconds Some switches especially if configured for VoIP require a longer time to complete Link negotiations and the Long setting will provide more consistent Link detection UPDATE PINGER SCREEN The Pinger Plus firmwar
bad Siber CableMaster 400 Voice Data amp Video Tester User Manual Tests Voice 6 wire Data 8 wire and Video coax Easy to read extra large 7 segment LCD screen with large icons Tone generation over voice data and video cables with 4 different tones RJ Voice amp Data master remote stores in bottom of case as Maps 19 locations at one time Tests and indicates pins with shorts opens reversals miswires and split pairs Displ